knikbioreactors
   lingua   
KNIK nuntium

Quo modo enim sterilitatem immaculatam ferro vexillum ante fermentum tristique?

Tempora: 2018-05-07 List:

Aliquam ferro sterilitate gradus vexillum piscinam: 

 

Nota:

1. Please carefully check the piping connections before sterilization to ensure that the piping installation is complete and reasonable.

2. Check the various interfaces, plug, silk mouth, fastening bolts on the tank   are installed intactly 

3. ready to air, steam, cooling water, etc.

4. turn off all the the action on the equipment, according to the need to decide whether we need to open the mixing (Or can open the sterilization process in the automatic sterilization)

5. sterilization process need to pay attention to the real-time state of the pressure gauge to ensure that the tank pressure and jacket pressure can not exceed 0.3MPa.

 

I: Illuminationes omnis vapor valvulae (LS1, LS1, LS2, LS3) ante foramen vapore valvae.

II: Prope est PA2 valvae, sed custodi ut Flowmeter aperta est versus in attractio in aere.) Propinquus SD3 valvae.

3: First open the exhaust valve VT1, open the jacke drain valve BD1 again, and finally open the jacket into the steam valve LS2. Heat the jacket by steam to warm the medium. (Note that at the beginning, BD1 valve can be fully open, when the jacket drain all the condensate , the appropriate small BD1 valve, keep the jacket with a certain pressure, but not more than 0.3MPa)

IV Close caeli cisternina vavle PA4 secessu longo locus: exhauriunt valvae aperiam in filter BD4 et exhauriunt valvae BD4, postremo valvae aperiam in secessu longo locus: Vapor LS3. (Nota ut ad adjust ostium valvae, et de fumo blowdown valvae ut pressura est stabilis in filter.)

V: Cum in piscinam temperatus excedit C ℃ et exhauriunt valvae et revolutus ad dispensationem oportet ut ad ostium VT5 pressura cisternina, sed non omnino clausus.

VI: LS6 valvae aperiam in vapor, F3, quia sampling sterilitate valvae; LS1 valvae aperiam in vapor, F4: imo valvae pro sterilitate. (Quod si necesse, cum piscinam temperatus pervenit CXV ℃ vel CXXI ​​℃, vos potest aperire S3 et F115, usque sampling valvae et cisternina valvae ad finem sterilitate, sed opus ad operam ad adjust vapor valvae LS121 F1 foramen est fundens supra materiam ne generation)


VII: Cum in piscinam temperatus pervenit CXV ℃ vel CXXI ​​℃, valvae aperiam in PA7, et vapor ire ad piscinam. Vapor pressura est in secessu longo locus debet esse major 115 MPa.

VIII: Cum temperatus pervenit usque ad CXXI ​​℃, vel velit pro XXX minutes tempore vel pro opportunitate ad redigendum usque ad tempus. (Et hoc oportet esse potest ad adjust ostium valvae et exhauriunt et vapor in tristique, ut enim pressura cisternina 8MPa vel circiter, sed non plus quam 121MPa.

IX: Cum Nulla consummatum est, S9 averte a velando dictae, F1: F2, F1. Deinde rursus omni off vapor LS3 valvis, LS1, LS2, et LS3 BD4 valvulae. Primum attractio valvae aperire PA1 tempora, adjust in exhauriunt valvae VT3, PA1 aperire. (In hoc est opus reddere operam ut filter ac tristique enim pressura maior quam externum environment).

10: When the tank temperature drops to 115 ° C, open the valve SD2, (note that there may be a beep at this time) in the program manually open the cooling valve, keep the intermittent water cooling.

11: After the tank temperature drops to 95 ° C, close the filter drain valve BD4 and the blow down valve BD3. Open the temperature control mode in the program or turn off the automatic control mode in the sterilization program to cool the tank.

XII: Cum in piscinam temperatus ad extra temperatus, fermentationem parati aperire modus, sterilitate finem.

 

Copyright © 2016-2020 Knik omnis elit ligula.