knikbioreactors
   teanga   
Nuacht KNIK

Conas is féidir linn an umar caighdeánach cruach dhosmálta a steiriliú roimh choipeadh?

Amanna: 2018-05-07 Brabhsáil:

Céimeanna steiriliú umar caighdeánach cruach dhosmálta: 

 

Nóta:

1. Please carefully check the piping connections before sterilization to ensure that the piping installation is complete and reasonable.

2. Check the various interfaces, plug, silk mouth, fastening bolts on the tank   are installed intactly 

3. ready to air, steam, cooling water, etc.

4. turn off all the the action on the equipment, according to the need to decide whether we need to open the mixing (Or can open the sterilization process in the automatic sterilization)

5. sterilization process need to pay attention to the real-time state of the pressure gauge to ensure that the tank pressure and jacket pressure can not exceed 0.3MPa.

 

1: Múch gach comhla gaile (LS1, LS2, LS3, LS4) sula n-osclaítear an comhla gaile.

2: Dún an comhla PA3, ach coinnigh an sreabhmhéadar ar oscailt chun a chinntiú go bhfuil aer ag an líne ionghabhála.) Dún an comhla SD2.

3: First open the exhaust valve VT1, open the jacke drain valve BD1 again, and finally open the jacket into the steam valve LS2. Heat the jacket by steam to warm the medium. (Note that at the beginning, BD1 valve can be fully open, when the jacket drain all the condensate , the appropriate small BD1 valve, keep the jacket with a certain pressure, but not more than 0.3MPa)

4: Dún an vavle umar inlet aeir PA4, oscail an comhla draein scagaire BD4 agus an comhla draein BD3, agus oscail an comhla inlet gaile LS1 sa deireadh. (Nóta chun oscailt na comhla gaile agus an chomhla séideadh a choigeartú chun an brú sa scagaire a choinneáil seasmhach.)

5: Nuair a sháraíonn teocht an umair 100 ℃, déan coigeartú iomchuí ar oscailt na comhla sceite VT1 lena chinntiú go mbeidh brú an umair, ach nach bhfuil sé dúnta go hiomlán.

6: an comhla gaile LS3, F1 a oscailt, le haghaidh steiriliú na comhla samplála; oscail an comhla gaile LS4, F3, le haghaidh steiriliú na comhla bun. (Más gá, nuair a shroicheann teocht an umair 115 ℃ nó 121 ℃, is féidir leat S1 agus F2 a oscailt, don chomhla samplála agus don chomhla umar ag deireadh an steiriliú, ach ní mór duit aird a thabhairt chun an comhla gaile LS3 agus F1 a oscailt chun an oscailt a choigeartú cosc a chur ar ghiniúint ábhar Doirt)


7: Nuair a shroicheann teocht an umair 115 ℃ nó 121 ℃, oscail an chomhla PA4, ionas go dtéann gaile isteach san umar. Caithfidh an brú gaile sa inlet a bheith níos mó ná 0.11 MPa.

8: Nuair a shroicheann an teocht 121 ℃, an insliú ar feadh 30 nóiméad nó mar is cuí chun an t-am a shíneadh nó an t-am a laghdú. (Ag an am seo is féidir a bheith oiriúnach chun an gaile a choigeartú san umar agus oscailt na comhla sceite, coinnigh brú an umair i thart ar 0.11MPa nó níos mó, ach ní mó ná 0.3MPa.

9: Nuair a bheidh an t-insliú críochnaithe, déan na comhlaí S1, F2, F1, F3 a mhúchadh. Ansin múch gach comhla gaile LS1, LS2, LS3, LS4 agus BD1. An chéad uair chun an comhla ionghabhála PA3 a oscailt, an comhla sceite VT1 a choigeartú, an PA4 a oscailt. (Ag an am seo ní mór aird a thabhairt chun a chinntiú go bhfuil an scagaire agus brú an umair níos mó ná an timpeallacht sheachtrach).

10: When the tank temperature drops to 115 ° C, open the valve SD2, (note that there may be a beep at this time) in the program manually open the cooling valve, keep the intermittent water cooling.

11: After the tank temperature drops to 95 ° C, close the filter drain valve BD4 and the blow down valve BD3. Open the temperature control mode in the program or turn off the automatic control mode in the sterilization program to cool the tank.

12: Nuair a shroicheann teocht an umair an teocht socraithe, réidh chun an modh coipeadh, deireadh steiriliú a oscailt.

 

Cóipcheart © 2016-2020 Knik Technology Gach ceart ar cosaint.